apsetup wavlink
apsetup wavlink
Read 3 minutes

Wavlink AC1200 Extender Setup

There are several steps involved in Wavlink AC1200 Extender Setup to guarantee the correct extension of your current WiFi network. It's important to keep in mind that depending on the brand and model of your extender, the exact steps may differ slightly, but the overall procedure will be very similar. In order to help you with the Wavlink AC1200 Extender Setup, here is a detailed guide.

  • Choose a location for your extender.
  • Your AC1200 extender must be plugged into an electrical outlet.
  • Connect to the WiFi network being broadcast by the extender using your laptop or mobile device.
  • On the device you're using to connect to the extender's network, launch a web browser.
  • Enter the extender's default IP address
  • To log in, you will be prompted. The default username and password can be found in the extender's manual.
  • Follow the on screen instructions to finalize the configuration process.

Depending on the maker and model, your Wavlink AC1200 Extender Setup procedure may differ slightly or require extra steps. Therefore, for the most precise and comprehensive instructions, it's crucial to always refer to the user manual that came with your particular AC1200 extender.

Wavlink AC1200 Extender Setup via WPS Method

WPS setup is a quick and easy way to set up your Wavlink Extender if your router also supports it.

Follow these steps to configure a Wavlink AC1200 Extender using WPS:

  • Connect your extender to a power source first, then wait for it to turn on.
  • When your extender is turned on, the power LED light goes solid green.
  • For three to five seconds, press and hold the WPS button on the extension until the WPS LED light starts to blink.
  • Within two minutes of pushing the WPS button on your extender, press the WPS button on your router.
  • Watch for the WPS LED light on your extender to become completely green; this shows that the extender and router have successfully connected.

After completing the setup process, you can relocate the extender and utilise it to expand your Wi-Fi network.

Wavlink AC1200 Extender Setup: common issues

Wavlink AC1200 Extender Setup, despite its straightforward nature, can sometimes encounter a few common issues. Here are some of the typical problems you might face and their underlying causes:

  • No Extender Networks Detected:
  • Can't Access the Extender's Web Interface:
  • Weak Extended WiFi Signal:
  • Incorrect Network Name or Password
  • Firmware Update Failure:
  • Extender Keeps Disconnecting:
  • Extender Not Broadcasting WiFi:
  • Unable to Connect to Extender's Network:
  • Extender Setup Stuck or Hanging
  • Extender LED Lights Abnormal

Troubleshooting tips for Wavlink AC1200 Extender Setup

  • Ensure the extender is powered on and the LED lights are active. Check if you're within the extender's coverage range.
  • Confirm that you're using the correct IP address to access the web interface.
  • Refer to the user manual to understand the LED light indicators meanings.
  • Ensure you're using the right firmware version for your extender model. Follow the firmware update process precisely.
  • Check for firmware updates that might address connectivity issues.
  • Place the extender far enough from other electronic devices to avoid interference and ensure peak performance.
  • Additionally, make sure the extender is turned on and set up correctly. If necessary, think about resetting the extender and starting the setup procedure all over again.
  • It's crucial to confirm that the extender keeps a connection to your primary WiFi network during the setup process. This step is essential for a smooth and effective setup process.

How to Update Firmware on Wavlink AC1200 Extender

It is important to keep your Wavlink WiFi extender firmware up to date. Firmware updates can improve the performance of your extender and fix any bugs or issues. Here's how to update your Wavlink WiFi extender's firmware:

  • Ensure the Wavlink wifi Extender is turned on and connected to your computer.
  • Launch a web browser on your computer and enter wifi.wavlink.com in the address bar.
  • Click on the “Administration” option and select the “Firmware Upgrade” option.
  • Click on the “Browse” button and locate the firmware upgrade file you downloaded from the Wavlink website.
  • Click on the “Upload” button to start the firmware upgrade process.
  • Wait for the firmware upgrading procedure to be completed.
  • The extender will restart automatically once the process is completed.